Telesto Clip on Light

Available Options:

Fixed Mounted or Removeable

Telesto Wall Mounting
Telesto Fixed Wall Mounting
Telesto Klamp-on & Economy Clamp
Telesto Tube Clamp and Bulldog Clip
Telesto Pop-On and Clip-On
Telesto Banner Bung Mounting
Telesto Slot-Over & Slot-In

Telesto LED - LED Spot lights (12V)

The Telesto LED spot lights are simple exhibition and display lighting.  The Telesto LED is a low voltage LED light ideally suited for display cabinet lighting.  Manufactured in a chrome or matt black finish the head swivels through 180 degrees allowing you to achieve the best cabinet lighting.  The Telesto LED uses the GU5.3 (MR16) LED bulb.  Like all our low voltage LED ranges, the Telesto LED is a simple yet stylish clip on light.

The Telesto LED requires a 240/12v LED driver: a tiny transformer like electronic driver.

To directly mount onto a wall or ceiling we have four options:

Telesto LED Cabinet Plate (CP)
is 25mm diameter with 3 screw holes.  This is ideal for mounting in cabinets or discretely on furniture or displays.

Telesto LED Ceiling Bracket (CB) is 74mm diameter with 4 screw holes.  This is ideal for built exhibition stands or shop fitting.

Telesto LED Cell Clamp (CC) is a simple right angled bracket with a hole in the base to bolt the light to a fixed surface (eg wall top or aluminium truss).  This provides a simple yet effective way to semi-permanently mount the light.

Telesto LED Wall Mount (WM) is designed to mount the light onto the top of a wall using 2 screws (not provided).  The arm can be mounted horizontally or tilted back above the horizontal using a simple tri-knob (un-tighten and re-tighten when in position)

To mount and dismantle your lighting we can offer the following nine removable options:

Telesto LED Economy Clamp (EC)
is a simple clamp mechanism tightened from the rear using the circular knob.  The clamp adjusts from 0mm - 57mm

Telesto LED Klamp-On (KO) is a robust versatile clamp allowing the arm and head to be positionned from horizontal to vertical as it comes out from the mount.  The klamp-on adjusts from 16mm to 60mm

Telesto LED Tube Clamp (TC) is our most versatile clamp, fitting tubes as well as boards.  With rubber grips and an adjustment from 5mm to 50mm this is ideal for clamping a light in those difficult positions

Telesto LED Bulldog Clip (BD) is the simplest clip when speed of getting on and off is required.  The very strong bulldog clip can clip to boards from 5mm to 50mm

Telesto LED Pop-on (PO) is designed for pop-up exhibition systems and simple clips under and over the cross members behind the graphics and is held in place by gravity.  So simple and easy to attach and take down it is the ideal complement to any pop-up system

Telesto LED Clip-on (CO / COMK / COSD) is a simple cantilevered clip for shell-schemes, aluminium profile exhibition systems and board systems with grooves.  Slotted into the groove or profile the light is simply held in place by gravity.  Very simple to use.  Call us to confirm the clip required

Telesto LED Banner Bung (BB) was designed for simple insertion into exhibition banners which have a hole in the upright pole.  Because of their simplicity they can also be used in some aluminium profile exhibition systems and in any built stand by drilling a hole into the mounting point.  Available in 8, 10, 12, 14mm bottom diameter

Telesto LED Slot Over (SO)
is a saddle which slots over a board or profile.  Easy on: easy off

Telesto LED Slot In (SI) is designed with 2 flat prongs to slot into the Nomadic exhibition system


Colours:                   Available in chrome or matt black                                                   

                                             We can match your colour scheme by request and at extra cost.

Arm Options:      100mm, 200mm, 300mm, 400mm (same price) & Swan Neck & 400mm Bendy Arm at extra cost.               

                                             We can manufacture the lights with a specific arm length by request and at extra cost

Bulb Options:  The Telesto LED uses the MR16 (GU5.3) 12V LED Bulb.  Our standard bulb is the 4W (equivalent to c. 20 watt halogen bulb) 

                                            Other bulbs are available please phone to discuss options.

LED Drivers:     The LED driver is smaller than an electronic transformer and wires up like a transformer.  We can provide this pre-wired in-line or supply the

                                           driver separately

All photographs above in chrome finish with 400mm arm

Other LED Spot Light Designs

      Microspot LED       Mimas LED         Hyperion LED      Janus LED         Callisto LED               Ganymede LED

                                               To BUY NOW click here