Callisto Head

Available Options:

Fixed Mounted or Removable

Callisto Cabinet Plate & Ceiling Bracket
Callisto Cell Clamp & Wall Mount
Callisto Klamp-on & Economy Clamp
Callisto Tube Clamp & Bulldog Clip
Callisto Pop-On & Clip-On
Callisto Banner Bung
Callisto Slot-Over & Slot-In

Callisto LED - Mains Voltage Display Lights

The Callisto LED spot lights are superb mains voltage exhibition lights.  Using the GU10 LED bulb these are chrome spotlights which are simple, stylish and manufactured to withstand hard knocks. These are the simplest, of all our LED spot lights range.  The head swivels through 180 degrees giving your display lights superb versatility.

The Callisto LED uses the GU10 LED bulb available in white or warm white

The Callisto LED light is usually supplied with a 4 metre cable terminating in a UK 3-pin plug, but can be adapted to your needs.  We can also supply all our mains LED lights on a "daisy chain system", where each light can be attached to the next in line and all connected back to a single mains plug (maximum 2000 watts).

To directly mount onto a wall or ceiling we have four options:

Callisto LED Cabinet Plate (CP)
is 25mm diameter with 3 screw holes.  This is ideal for mounting in cabinets or discretely on furniture or displays.

Callisto LED Ceiling Bracket (CB) is 74mm diameter with 4 screw holes.  This is ideal for built exhibition stands or shop fitting.

Callisto LED Cell Clamp (CC) is a simple right angled bracket with a hole in the base to bolt the light to a fixed surface (eg wall top or aluminium truss).  This provides a simple yet effective way to semi-permanently mount the light.

Callisto LED Wall Mount (WM) is designed to mount the light onto the top of a wall using 2 screws (not provided).  The arm can be mounted horizontally or tilted back above the horizontal using a simple tri-knob (un-tighten and re-tighten when in position)

To mount and dismantle your lighting we can offer the following nine removable options:

Callisto LED Economy Clamp (EC)
is a simple clamp mechanism tightened from the rear using the circular knob.  The clamp adjusts from 0mm - 57mm

Callisto LED Klamp-On (KO) is a robust versatile clamp allowing the arm and head to be positionned from horizontal to vertical as it comes out from the mount.  The klamp-on adjusts from 16mm to 60mm

Callisto LED Tube Clamp (TC) is our most versatile clamp, fitting tubes as well as boards.  With rubber grips and an adjustment from 5mm to 50mm this is ideal for clamping a light in those difficult positions

Callisto LED Bulldog Clip (BD) is the simplest clip when speed of getting on and off is required.  The very strong bulldog clip can clip to boards from 5mm to 50mm

Callisto LED Pop-on (PO) is designed for pop-up exhibition systems and simple clips under and over the cross members behind the graphics and is held in place by gravity.  So simple and easy to attach and take down it is the ideal complement to any pop-up system

Callisto LED Clip-on (CO / COMK / COSD) is a simple cantilevered clip for shell-schemes, aluminium profile exhibition systems and board systems with grooves.  Slotted into the groove or profile the light is simply held in place by gravity.  Very simple to use.  Call us to confirm the clip required

Callisto LED Banner Bung (BB) was designed for simple insertion into exhibition banners which have a hole in the upright pole.  Because of their simplicity they can also be used in some aluminium profile exhibition systems and in any built stand by drilling a hole into the mounting point.  Available in 8, 10, 12, 14mm bottom diameter

Callisto LED Slot Over (SO)
is a saddle which slots over a board or profile.  Easy on: easy off

Callisto LED Slot In (SI) is designed with 2 flat prongs to slot into the Nomadic exhibition system


Colours:                   Available in chrome or matt black.                                                       

                                             We can match your colour scheme by request and at extra cost.

Arm Options:      100mm, 200mm, 300mm, 400mm (same price) & Swan Neck (at extra cost).               

                                             We can manufacture the lights with a specific arm length by request and at extra cost

Bulb Options:   The Callisto LED uses the GU10 LED Halogen Bulb.  Our standard bulb is the 4W, 36 degree, 30,000 hour bulb (which is equivalent to a 35W

                                             halogen bulb)                                          

                                             We can supply other wattages on request

All photographs above in chrome with 400mm arm

Other LED Spot Light Designs

      Microspot LED       Mimas LED         Telesto LED       Hyperion LED       Janus LED       Ganymede LED

                                                To BUY NOW click here