Retro - Mains Voltage Display Lights
The Retro light Is a traditional mains spotlight. These Retro clip lights use the conventional Edison screw-in R80 bulb in either 60W or 100W. The Retro light is the ultimate in easy use, as simple clip lights or securely mounted onto fixed walls. Finished in a durable matt-black and with a head that swivels through 180 degrees giving your display lights superb versatility, this is the first choice whenever a retro style is needed or when the light from the bulb itself needs to be shaded (as in lighting for dart boards)
The Retro light is usually supplied with a 3 metre cable terminating in a UK 3-pin plug, but can be adapted to your needs. We can also supply all our mains lights (and low voltage lights with in-line transformers) on a "daisy chain system", where each light can be attached to the next in line and all connected back to a single mains plug (maximum 2000 watts).
Retro Cabinet Plate (CP) is 25mm diameter with 3 screw holes. This is ideal for mounting in cabinets or discretely on furniture or displays.
Retro Ceiling Bracket (CB) is 74mm diameter with 4 screw holes. This is ideal for built exhibition stands or shop fitting.
Retro Cell Clamp (CC) is a simple right angled bracket with a hole in the base to bolt the light to a fixed surface (eg wall top or aluminium truss). This provides a simple yet effective way to semi-permanently mount the light.
Retro Wall Mount (WM) is designed to mount the light onto the top of a wall using 2 screws (not provided). The arm can be mounted horizontally or tilted back above the horizontal using a simple tri-knob (un-tighten and re-tighten when in position)
To mount and dismantle your lighting we can offer the following ten removable options:
Retro Economy Clamp (EC) is a simple clamp mechanism tightened from the rear using the circular knob. The clamp adjusts from 0mm - 57mm
Retro Klamp-On (KO) is a robust versatile clamp allowing the arm and head to be positionned from horizontal to vertical as it comes out from the mount. The klamp-on adjusts from 16mm to 60mm
Retro Tube Clamp (TC) is our most versatile clamp, fitting tubes as well as boards. With rubber grips and an adjustment from 5mm to 50mm this is ideal for clamping a light in those difficult positions
Retro Bulldog Clip (BD) is the simplest clip when speed of getting on and off is required. The very strong bulldog clip can clip to boards from 5mm to 50mm
Retro Pop-on (PO) is designed for pop-up exhibition systems and simple clips under and over the cross members behind the graphics and is held in place by gravity. So simple and easy to attach and take down it is the ideal complement to any pop-up system
Retro Clip-on (CO / COMK / COSD) is a simple cantilevered clip for shell-schemes, aluminium profile exhibition systems and board systems with grooves. Slotted into the groove or profile the light is simply held in place by gravity. Very simple to use. Call us to confirm the clip required
Retro Banner Bung (BB) was designed for simple insertion into exhibition banners which have a hole in the upright pole. Because of their simplicity they can also be used in some aluminium profile exhibition systems and in any built stand by drilling a hole into the mounting point. Available in 8, 10, 12, 14mm bottom diameter
Retro Slot Over (SO) is a saddle which slots over a board or profile. Easy on: easy off
Retro Slot In (SI) is designed with 2 flat prongs to slot into the Nomadic exhibition system
Options:
Colours: Available in matt black.
We can match your colour scheme by request and at extra cost.
Arm Options: 100mm, 200mm, 300mm, 400mm (same price) & Swan Neck (at extra cost).
We can manufacture the lights with a specific arm length by request and at extra cost
Bulb Options: The Retro uses the R80 Bulb. Our standard bulb is the 60W or 100W, 1000 hour bulb.
