Aardvark Display Lighting 07753 796306

Hyperion - Low Voltage Exhibition Lighting                        BUY NOW

The Hyperion exhibition light is the ultimate minimalist spot light for all displays, cabinets and exhibition work.  The Hyperion light is the minimal way to mount the 12v, 50W, halogen, diachroic, low voltage spotlight bulb.  The effect is clear crisp light delivered in a simple stylish way.  Finished in chrome or matt black the head swivels through 180 degrees allowing you to achieve the best exhibition light.  Like all low voltage lighting the Hyperion light is ideal for graphics,  colours or jewels.

The Hyperion requires a transformer but we have 2 simple options:

• The Eazi-uze 4-light pack provides everything you need when you arrive at the exhibition, 4 lights, transformer and bulbs in a re-useable carry case, with a simple jack-plug and sockets, no tools or experts are required.
• Our in-line version hard-wires a small electronic transformer in-line so that this low voltage lighting can be plugged directly into the mains.

To directly mount onto a wall or ceiling we have four options:


Hyperion Cabinet Plate (CP) is 25mm diameter with 3 screw holes.  This is ideal for mounting in cabinets or discretely on furniture or displays.



Hyperion Ceiling Bracket (CB) is 74mm diameter with 4 screw holes.  This is ideal for built exhibition stands or shop fitting.










Hyperion Cell Clamp (CC) is a simple right angled bracket with a hole in the base to bolt the light to a fixed surface (eg wall top or aluminium truss).  This provides a simple yet effective way to semi-permanently mount the light.

Hyperion Wall Mount (WM) is designed to mount the light onto the top of a wall using 2 screws (not provided).  The arm can be mounted horizontally or tilted back above the horizontal using a simple tri-knob (un-tighten and re-tighten when in position)

To mount and dismantle your lighting we can offer the following ten removable options:

Hyperion Economy Clamp (EC) is a simple clamp mechanism tightened from the rear using the circular knob.  The clamp adjusts from 0mm - 57mm



Hyperion Klamp-On (KO) is a robust versatile clamp allowing the arm and head to be positionned from horizontal to vertical as it comes out from the mount.  The klamp-on adjusts from 16mm to 60mm








Hyperion Tube Clamp (TC) is our most versatile clamp, fitting tubes as well as boards.  With rubber grips and an adjustment from 5mm to 50mm this is ideal for clamping a light in those difficult positions



Hyperion Bulldog Clip (BD) is the simplest clip when speed of getting on and off is required.  The very strong bulldog clip can clip to boards from 5mm to 50mm







Hyperion Pop-on (PO) is designed for pop-up exhibition systems and simple clips under and over the cross members behind the graphics and is held in place by gravity.  So simple and easy to attach and take down it is the ideal complement to any pop-up system



Hyperion Clip-on (CO / COMK / COSD) is a simple cantilevered clip for shell-schemes, aluminium profile exhibition systems and board systems with grooves.  Slotted into the groove or profile the light is simply held in place by gravity.  Very simple to use.  Call us to confirm the clip required







Hyperion Jack-Plug (JP) is the ideal removeable lighting system.  Mount the jack socket into a wall or ceiling with the cable hidden behind the wall and the light simply pushes and locks in place and a simple red button on the jack socket allows easy and swift removal












Hyperion Banner Bung (BB) was designed for simple insertion into exhibition banners which have a hole in the upright pole.  Because of their simplicity they can also be used in some aluminium profile exhibition systems and in any built stand by drilling a hole into the mounting point.  Available in 8, 10, 12, 14mm bottom diameter








Hyperion Slot Over (SO) is a saddle which slots over a board or profile.  Easy on: easy off






Hyperion Slot In (SI) is designed with 2 flat prongs to slot into the Nomadic exhibition system