Ganymede - Mains Voltage Clip Light BUY NOW
Ganymede Spot Lighting gives a stylish look to any display with the mains halogen GU10 bulb discretely covered by the Ganymede head. These clip lights are ideal for exhibitions and moveable or POP displays, but are equally at home in shop fit-outs or even in domestic situations. Spot Lighting with clip lights is often hampered by the visual impact of the bulb housing; with the Ganymede this is completely eliminated, yet there is enough purchase to easily remove and replace old bulbs. These clip lights are manufactured to withstand hard knocks finished in anodised aluminium or in matt-black. The head swivels through 180 degrees giving your spotlighting superb versatility.
The Ganymede lights clip on to your display and are usually supplied with a 4 metre cable terminating in a UK 3-pin plug, but can be adapted to your needs. We can also supply all our mains lights (and low voltage lights with in-line transformers) on a "daisy chain system", where each light can be attached to the next in line and all connected back to a single mains plug (maximum 2000 watts).
Ganymede clip lights can be supplied in an Eazi-uze 4-light pack which provides everything you need when you arrive at the exhibition: 4 lights, daisy chain connector cables so that you have only a single mains plug, GU10, 50W bulbs and all in a re-useable carry case. no tools or experts are required.
Ganymede Tube Clamp (TC) is our most versatile clamp, fitting tubes as well as boards. With rubber grips and an adjustment from 5mm to 50mm this is ideal for clamping a light in those difficult positions
Ganymede Bulldog Clip (BD) is the simplest clip when speed of getting on and off is required. The very strong bulldog clip can clip to boards from 5mm to 50mm
To directly mount onto a wall or ceiling we have four options:
Ganymede Cabinet Plate (CP) is 25mm diameter with 3 screw holes. This is ideal for mounting in cabinets or discretely on furniture or displays.
Ganymede Ceiling Bracket (CB) is 74mm diameter with 4 screw holes. This is ideal for built exhibition stands or shop fitting.
Ganymede Cell Clamp (CC) is a simple right angled bracket with a hole in the base to bolt the light to a fixed surface (eg wall top or aluminium truss). This provides a simple yet effective way to semi-permanently mount the light.
Ganymede Wall Mount (WM) is designed to mount the light onto the top of a wall using 2 screws (not provided). The arm can be mounted horizontally or tilted back above the horizontal using a simple tri-knob (un-tighten and re-tighten when in position)
To mount and dismantle your lighting we can offer the following nine removable options:
Ganymede Economy Clamp (EC) is a simple clamp mechanism tightened from the rear using the circular knob. The clamp adjusts from 0mm - 57mm
Ganymede Klamp-On (KO) is a robust versatile clamp allowing the arm and head to be positionned from horizontal to vertical as it comes out from the mount. The klamp-on adjusts from 16mm to 60mm
Ganymede Pop-on (PO) is designed for pop-up exhibition systems and simple clips under and over the cross members behind the graphics and is held in place by gravity. So simple and easy to attach and take down it is the ideal complement to any pop-up system
Ganymede Clip-on (CO / COMK / COSD) is a simple cantilevered clip for shell-schemes, aluminium profile exhibition systems and board systems with grooves. Slotted into the groove or profile the light is simply held in place by gravity. Very simple to use. Call us to confirm the clip required
Ganymede Banner Bung (BB) was designed for simple insertion into exhibition banners which have a hole in the upright pole. Because of their simplicity they can also be used in some aluminium profile exhibition systems and in any built stand by drilling a hole into the mounting point. Available in 8, 10, 12, 14mm bottom diameter
Ganymede Slot Over (SO) is a saddle which slots over a board or profile. Easy on: easy off
Ganymede Slot In (SI) is designed with 2 flat prongs to slot into the Nomadic exhibition system
Options:
Colours: Available in anodised aluminium or matt black.
We can match your colour scheme by request and at extra cost.
Arm Options: 100mm, 200mm, 300mm, 400mm (same price) & Swan Neck (at extra cost).
We can manufacture the lights with a specific arm length by request and at extra cost
Bulb Options: The Ganymede uses the GU10 Diachroic Halogen Bulb. Our standard bulb is the 50W, 35 degree, 2000 hour bulb.
We can supply other wattages and colours on request
